STRATA collection

TERAS Cordless Lamp

TERAS is a small cordless lamp shaped like a core sample: a cylinder of bands of uneven height, separated by thin lines that glow when it is on. Lit, it is warm and banded like layered rock; unlit, a plain white cylinder with fine horizontal grooves. At 8.8 cm across it fits a crowded nightstand, a dressing table or a shelf, and it is the easiest lamp in the range to give. RM 149. Made for you after you order, and ships within 7 days. Ø8.8 × 12.9 cm, bone white. A rechargeable LED charges through a USB-C port at the back of the base.

Ø8.8 × 12.9 cm

Colour Bone white

Price: RM 149

Made for you after you order. Ships within 7 days.

Ship-by date: within 7 days of your order.

Shipping is calculated at checkout.

STRATA collection

Where it comes from

TERAS is part of STRATA, a collection that comes from layers: geological core samples, contour lines, and the layer-by-layer way these lamps are made. Teras means core. The bands are the record of a column drawn out of the ground.

Making factIt prints in vase mode as one continuous spiral wall, so the shell has no seam at all.

The form

A single cylinder in which thick and thin wall sections alternate. The thin sections pass more light and read as bright lines; the thick ones stay softer. The battery and LED sit in the base, and show through as a gentle shadow when it is lit.

In the room

TERAS is the smallest of the lamps and the most portable. Carry it from the bedside to the dressing table to the dinner table; it gives a low, warm light rather than lighting a whole room.

How it's made

TERAS prints in vase mode, a single continuous spiral wall, so there is no seam anywhere on the shell. The bands are thick and thin sections of that one wall. The light is a ready-made rechargeable LED module with its own charge protection.

TERAS was the simplest idea of the twelve: let the layers be the decoration. It is also the lamp I would hand someone first. — Fakhrul

Designed by Fakhrul

The essentials

  • Made in Malaysia
  • Ships within 7 days
  • Cordless, recharges by USB-C
Details

Details at a glance

TERAS specifications
DimensionsØ8.8 × 12.9 cm (diameter × height)
Material: ShellBone-white PLA
Material: LightRechargeable LED module with USB-C (bought in)
LightLED, integrated module
PowerRechargeable battery
ChargingUSB-C
ColourBone white
Made inMalaysia
Safety and care

Safety and care

Charge it through the USB-C port with a standard USB-C cable. The printed parts are PLA, which softens at around 55–60 °C, so keep the lamp out of direct sun and parked cars, and away from heaters. Indoor use, in a dry room. More on care.

Shipping, returns, warranty

Shipping, returns and warranty

Every lamp is made for you after you order and ships within 7 days. Read shipping and returns and the warranty. None of this affects your rights under the Consumer Protection Act 1999.

Questions

Questions

How do I charge it?

With a USB-C cable, through the USB-C port on the base. The light is a ready-made rechargeable LED module with its own charge protection.

How long does a charge last?

We only publish measured numbers, and the run time is being tested: [OWNER: measured battery hours and charge time].

How do I clean it?

Switch it off (and unplug it, if it has a cord), then dust it with a soft dry brush or a microfibre cloth. No water inside the lamp and no solvents.

Will I see layer lines?

Up close, yes. Fine horizontal lines are the trace of how the lamp is 3D printed, and we keep them even and quiet rather than hiding them. Every lamp is switched on in a dark room and inspected at an angle before it ships, because that is how you will see it.

How long until it ships?

We make it after you order, and it ships within 7 days. Transit time depends on where you are: see shipping and returns.

Is it a good gift?

Yes, it is an easy one to give: small, cordless and calm, at our entry price.

Read

More about TERAS